Cyber-Physical Risk: How IoT Faults Can Trigger Electrical Fires in Industrial Networks
IoT fire risk in an industrial plant comes from hacked controls, alarms that reach no one, loose terminations and overloaded circuits. What we check.


Contents
- Cyberattacks Can Manipulate Physical Systems into Dangerous States
- Integration Gaps Leave Dangerous Blind Spots
- Poor Installation Leaves Connections That Run Hot
- Overloading and Load Imbalance from Added Equipment
- Most Common IIoT Points of Failure
- Best Practices for Engineering Teams and Facility Managers
- Don’t Let Smart Devices Cause Dumb Fires
In an industrial plant, IoT fire risk comes from four main places, and only one of them involves a hacker. The other three are mundane: an alarm that never reaches anyone, a termination nobody torqued, and new load on a circuit with no room to spare.
Key takeaways
- In an industrial plant, IoT fire risk comes from four main places, and only one of them involves a hacker.
- The other three are an alarm that never reaches anyone, a termination nobody torqued, and new load on a circuit with no room to spare.
- Every wired sensor, gateway and panel meter adds terminations, and a connection not torqued to spec can run hot at normal current without tripping the breaker.
- Most facilities mix legacy electrical systems with newer connected platforms, which leaves integration gaps.
Industrial IoT (IIoT) equipment does real work. Remote monitors on cathodic protection rectifiers save trips to the field, and meters on switchgear show an overloaded phase while there is still time to fix it. But every device is also an electrical installation, and many are a door into the control network.
Cyberattacks Can Manipulate Physical Systems into Dangerous States
Manufacturers are a bigger target than they used to be. NTT’s 2021 threat report counted a 300% jump in attacks on manufacturing in 2020. Manufacturing, health care and finance together drew 62% of all attacks that year.
Phishing and ransomware get the headlines. For fire, the attacks that matter are the ones that reach SCADA systems and the IIoT devices tied to them. A compromised controller can override a safety limit and report false temperature or voltage readings at the same time. The screen shows a normal process while the equipment overheats.
Attackers have already gone after safety systems. In 2017, malware known as TRITON reached the safety controllers at an oil refinery in the Middle East. Those controllers exist to shut the process down safely when conditions turn dangerous. A 2022 CISA advisory says the attack left the refinery shut down for several days.
Integration Gaps Leave Dangerous Blind Spots
Most industrial facilities run a mix of legacy electrical systems and newer connected platforms: distribution monitoring, HVAC automation, lighting control, energy management, remote machine control. Where those systems don’t share data cleanly, signals get missed and responses to failures come late. The gaps rarely show up on a drawing. They turn up when someone walks the site, which is one reason we push for routine electrical audits.
Picture a plant that put wireless temperature sensors on its main switchgear. A bus joint starts running hot and the sensor reports it. But the gateway lost its link to the monitoring system after a network change months ago, and nobody noticed. A screen with no alarms looks the same as a screen with nothing wrong. The joint keeps heating until it fails.
Poor Installation Leaves Connections That Run Hot

Every wired sensor, gateway and panel meter adds terminations, and each one is a place for heat to build if it isn’t made up right. A connection that wasn’t torqued to spec can loosen, oxidize and run hot at perfectly normal current. The breaker won’t help. As a CPSC paper on arc-fault breakers explains, the current through a loose connection is limited by the load. It is usually well under the breaker’s rating, so a standard breaker doesn’t trip.
Have an electrical engineer review IIoT hardware before it goes in, not after. Start with an electrical load analysis on the circuits involved. Then confirm every termination is torqued and marked, and find out where each device actually gets its power. “Plug and play” devices need the most attention, because they tend to end up on whatever receptacle or control circuit is closest. When there is a fire, the connections in the area of origin get a close look from our forensic engineers.
Overloading and Load Imbalance from Added Equipment
The efficiency case for IIoT is real. A GE Vernova blog post on connected manufacturing sums up the idea. Sensors on the equipment gather data, pass it along wirelessly, and feed the analytics and machine learning that act on it.
The sensors themselves draw very little. The load comes from what arrives with them: network switches, PoE injectors, edge computers, UPS units, enclosure heaters and fans. That gear often gets plugged into 120-volt circuits laid out years ago for something else, sometimes all on one phase. Its electronic power supplies also add harmonic current, which piles up on shared neutrals that were never sized for it. Add a few pieces at a time for a few years and a branch circuit or panel ends up carrying more than anyone planned. A regular electrical load analysis catches that while the fix is still cheap.
Most Common IIoT Points of Failure
What works for a waste-to-energy plant in Houston won’t always carry over to a recycling plant in Maine. Still, the same failure points come up again and again:
- Sensor readings that drift, freeze or get flagged as bad quality
- Control failure with PLCs or controllers that don’t have a backup power source in place
- Control communication failure due to network communication errors
- Firmware and software left unpatched for months or years
- Faulty or overloaded circuits
- Poor installation and maintenance
- Aging or damaged equipment
- Cyberattacks gaining control of connected industrial settings
- Heat, dust, moisture and vibration inside enclosures
- Gross negligence from improper training and oversight
Done right, IIoT lowers fire risk. A temperature sensor on a bus joint will flag the kind of loose connection a breaker never sees. Current monitoring shows a circuit creeping toward its limit. Some systems can even shed load or isolate a fault on their own. All of it depends on the network actually delivering the data, and on someone who knows what to do when an alarm comes in.
Best Practices for Engineering Teams and Facility Managers
At Dreiym Engineering, we don’t want to come to your location for a forensic engineering consultation after a fire. If we’re there, it means something really bad happened, and you need an expert. We’d much rather help you prevent any damage in the first place. Here is what we would do in your place:
- Schedule a regular electrical load analysis so load imbalance and circuit stress don’t go unnoticed, and run one before any large IIoT rollout.
- Use internal teams or outside consultants for cyber-physical audits that check how your digital systems interact with the physical equipment, especially switchgear and control rooms.
- Limit who and what can reach SCADA and IIoT devices, and change default passwords and settings before anything goes live. NIST’s Guide to Operational Technology (OT) Security covers the details.
- Bring your monitoring systems (HVAC, electrical, backup power, water) onto one dashboard your managers actually check. Have it alarm when data stops arriving, not just when a reading goes out of range.
- Have panels and terminations scanned with a thermal camera under load after new equipment goes in, then on a regular schedule.

Last, have someone qualified check every installation before it goes live. Don’t hand sensor installs to an intern who hasn’t been trained for it. The right person gets the system running and leaves your team knowing how to maintain it and what an early fault looks like.
Don’t Let Smart Devices Cause Dumb Fires
Every sensor or controller you add brings more visibility and one more thing that can fail. Treat cyber-physical security as part of fire safety, not a separate IT project, and that trade stays in your favor.
If you are adding connected equipment, or already have it and aren’t sure what it’s tied into, talk to our team at Dreiym Engineering. We do electrical audits, load balancing, ground testing and short-circuit analysis. If the worst happens, we also handle industrial fire investigation for owners, insurers and attorneys.